How To Clean Convair Prestige Evaporative Cooler

Download Commodity

Download Article

A dissever system air conditioner is a groovy option for keeping your home cool and comfortable in the summer months. These units are as well quieter, easier to install, and more energy efficient than central air-conditioning. This blazon of A/C is ductless, so all y'all have to exercise is install the cooling unit within and the compressor and condenser unit outside, then run piping and a power cable between the units. If y'all don't want to hire a professional person to install a split system air conditioner and you accept some feel with plumbing and electrical work, you can install the unit on your ain. Each air conditioning unit is unique to its manufacturer, only the general installation process is the same.

1. 1

   Select an unobstructed location on your interior wall to mountain the indoor unit of measurement. You'll need to cutting a hole through the wall to feed the pipes from the indoor unit to the outdoor unit, then make certain the location y'all choose volition allow y'all to exercise so. Choose a spot abroad from direct sunlight and oestrus sources for the all-time results. Mount the unit 7 feet (2.1 m) off the floor and ensure there'south at least vi–12 inches (xv–30 cm) of open infinite on every side of the unit to allow for proper airflow.^[1]

   • Choose a location with studs to ensure the wall is stiff plenty to hold the weight of the unit.
   • Install the unit at least three.3 anxiety (i.0 m) away from antennas and power or connecting lines that are used for tv, radio, home security systems, intercoms, or telephones. The electric racket from these sources could cause operational bug for your air conditioner.
   • Avoid locations where gas may leak or where oil mist or sulfur exists.
   • Near of these units have remote controls so that yous tin can hands turn them on or off and adjust the temperature even if they're mounted high on the wall.

   Tip: Choose a cardinal location for the indoor unit of measurement where the cool air tin easily menstruum through your home, such as in the living room.

2. 2

   Secure the mounting plate to the interior wall. Hold the mounting plate against the wall where you want to install the indoor unit. Utilise a level to make sure it is both horizontally and vertically level. Use a pencil to mark the locations of the screw holes, remove the plate, then drill a hole into the wall where each screw will become.^[two]

   • Position the plate then information technology matches upwardly with the holes, insert plastic anchors into the holes, and secure the plate to the wall with tapping screws.

   Advertisement

3. iii

   Drill a 3 in (7.6 cm) hole through the wall so y'all tin can feed the pipes outside. Make a marking in the heart of the hole in the mounting plate. Employ a keyhole saw or a drill with a hole-cutting zipper to create a circular iii in (seven.vi cm) opening through the wall that slopes slightly downward toward the ground to ensure adequate drainage.^[3]

   • Make sure there are no pipes or wires behind the wall before drilling or cut the hole.

4. iv

   Check the electrical connections on the indoor unit. Elevator the A/C unit of measurement's front panel and remove the cover. Make sure the cable wires are connected to the screw terminals and that the wiring matches the diagram that came with the unit.

5. 5

   Run the pipes and cables through the hole in the wall, then connect them to the unit. Secure the included copper pipes, power cable, and drain pipe together with electric tape. Place the drain pipe on the lesser to ensure a free catamenia of h2o. Run the pipes and cable through the hole in the wall, and then secure them to the designated spots on the indoor unit as directed past the instruction manual.

   • Each line comes pre-insulated, so y'all don't have to worry nearly calculation extra insulation.
   • Practise your best to minimize how much the pipes and cable bend to ensure that the unit of measurement performs well.
   • Brand sure that the drainage pipage allows h2o to drain in an appropriate identify. Come across the instruction manual included with your kit for more than information.

6. 6

   Secure the indoor unit of measurement to the mounting plate. To attach the air conditioner to the wall, simply align the female connections on the dorsum of the unit with the male person connections on the mounting plate and press firmly to secure the unit of measurement in identify. Make sure the unit tilts astern 2-3 degrees so that water can flow out of the drain piping.^[4]

   • It may help to have a friend hold the unit in place while you secure the connections.

   Advertisement

1. 1

   Position the outdoor unit away from any heavily trafficked, dusty, or hot areas. Discover the hole you lot drilled through the mounting plate for the interior unit and position the exterior unit of measurement within 50 feet (15 yard) so the piping and cable can easily exist fastened.^[five] Choose a location with at least 12 inches (30 cm) of space surrounding its perimeter to ensure proper functioning. If possible, select a shady location that's sheltered from the air current in addition to dust and traffic to keep your unit of measurement functioning at its all-time.

   • Make certain that no antenna of a radio or television is within 10 feet (3.0 m) of the outdoor condenser.

2. 2

   Lay a concrete pad on the ground. Don't place the outdoor unit straight on the ground, as it's heavy and can shift around on clay or rocks. It's necessary to install the condenser on a concrete pad, which you can find at dwelling house improvement stores. Position the pad where yous want to install the unit and utilize a level to brand sure it's apartment and fifty-fifty.^[6]

   Tip: Situate the concrete pad so that it's loftier enough to go along the unit out of any water that may pool on the ground due to rain or snow.

3. 3

   Secure the outdoor unit on height of the physical pad. Lay a safe absorber on top of the pad to minimize vibration, then set the outdoor condenser unit on top of the pad. Secure the unit to the concrete with anchor bolts.^[7]

4. 4

   Check the electrical wiring in the outdoor unit. Remove the cover on the condenser. Refer to the unit of measurement'due south wiring diagram in the instruction manual and make sure the wires are connected as the diagram suggests. Make whatever adjustments as necessary.

   • Spike the cables with a cable clench and supplant the comprehend.

5. five

   Connect the piping and cablevision to the outdoor unit. Use flare basics to secure the 2 copper pipes from the indoor unit to the outdoor unit every bit per the instruction transmission. Connect the ability cablevision that runs from the indoor unit to the outdoor unit of measurement as well.

   • Finally, connect the power supply to a designated outlet.
   • If necessary, y'all tin trim the copper pipes to eliminate excess.

   Advertisement

1. one

   Drain the air and humidity from the refrigerant circuit. Remove the caps from the 2-way and three-manner valves and from the service port and connect a vacuum pump hose to the service port. Plow the vacuum on until it reaches an accented vacuum of 10mm Hg. Close the low pressure level knob and and then turn off the vacuum.

   • Exam all of the valves and joints for leaks, then disconnect the vacuum. Replace the service port and caps.

2. 2

   Affix the piping to the wall with clamps. To ensure the pipes and cables don't motion around or go asunder, attach them to the exterior wall of your dwelling using the clamps that came with the kit. Follow the directions in the manual to ensure the clamps are spaced adequately.

3. 3

   Seal up the pigsty in the wall using expanding polyurethane foam. Spray expanding polyurethane foam into the hole you drilled to feed the cable and pipe through the wall. Make certain the hole is completely sealed to preclude hot air or insects from getting through.

   • Let the cream dry out as per the instructions on the label before turning on your air conditioning.

4. 4

   Turn on the unit and enjoy the cool air! All that'southward left to do is to starting time the A/C, which you can practice from the indoor unit. It should only take a minute or two for cool air to start blowing into your home.^[8]

   • Refer to the instruction transmission if you lot take whatever trouble operating your new air conditioner.

   Advertisement

Add New Question

• Question

  How should I maintain my Ac unit?

  

  Victor Belavus is an Air Conditioning Specialist and the Possessor of 212 HVAC, an air condition repair and installation company based in Brooklyn, New York. In add-on to HVAC and air conditioning units, Victor also specializes in furnace repair and air duct cleaning. He has over 10 years of feel working with HVAC systems.

  

  Air Conditioning Specialist

  Proficient Answer

  Nigh homeowners shouldn't do extensive maintenance themselves—rent a professional for that. Withal, yous should be replacing your filters at least every 3 months, and audit your outdoor condenser for any debris, too. I would also recommend covering your Air conditioning condenser for the wintertime to protect information technology from snowfall.

Inquire a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advertisement

Video

• Provide a dedicated power outlet for your air conditioner.

• Always follow the manufacturer'due south instructions that come up with your split system air conditioner.

• Since a separate organisation Air conditioning is ductless, information technology'due south less susceptible to air leaks, which ways it's frequently a more energy-efficient solution.^[ix]

• Brand certain to choose the proper size air conditioner for your home to ensure it's free energy efficient.^[10]

• Check your outdoor condenser for debris and replace your air conditioner filter regularly—at least every 3 months.^[11]

• If you want a separate unit system that can both absurd and estrus your home, get a split arrangement heat pump, or mini-split. These units act every bit both air conditioners and heaters.^[12]

Advertisement

• Do non permit whatever wiring to touch the compressor, refrigerant tubing, or any moving fan parts.

• If you live in a land where it is legal to install a split arrangement air conditioning unit without professional qualifications, you must still follow all municipal codes for electrical wiring and other aspects of the installation.

• Some carve up organisation air conditioner manufacturers void the unit of measurement's warranty if information technology is not installed by a licensed tradesman.

• If you are based in the Eu, you must have your split organization ac unit installed by a qualified F-Gas engineer in accordance with EC/517/2014. Information technology is illegal to install these systems without the appropriate qualifications.

Advertisement

Things You'll Need

• Stud finder
• Level
• Pencil
• Plastic anchors
• Borer screws
• Keyhole saw
• Drill with hole-cutting attachment
• Electric record
• Wrenches
• Cable clamps
• Vacuum pump
• Expanding polyurethane foam

Virtually This Commodity

Article Summary Ten

It's best to hire a professional person to install a carve up system air conditioner. However, if yous decide to exercise the work yourself, mount the indoor air conditioning unit on an interior wall away from direct heat or light sources. Run the pipe and wiring from the indoor unit through a hole in the wall, and so attach a PVC drainage pipe to the unit, running down the exterior of the wall where the unit of measurement is attached. Next, install the outdoor condenser on a level concrete pad, then connect the electrical wires and the copper pipes. Keep reading to learn how to bleed the air and humidity from the refrigerant excursion!

Did this summary help you?

Cheers to all authors for creating a page that has been read 1,127,162 times.

Did this article help you lot?

Source: https://www.wikihow.com/Install-a-Split-System-Air-Conditioner

Posted by: lewellenforneved.blogspot.com

Share this post